NIX 521

Tomy

NIX-521, a dual-temp centrifuge that combines functions of refrigerated centrifuge and thermostatic centrifuge provide wide temperature setting range (-9℃ to 42℃). Thermostatic function with centrifuge is used for application such as “Gene transfer to hemopoietic stem cell” and “Development of vector for anti-cancer immunity”.

Accessories here

NIX-521 has function of air circulation, which left heated air in and out from bottom of chamber lid. Because of these inlet and outlet of air at bottom of chamber lid, no heater element is in chamber for safety.

Features

Three-step acceleration and three-step and natural deceleration

Initial values for acceleration and deceleration characteristics are set from 0 to 500rpm, however, they can be varied up to maximum speed in 100rpm increments by function settings.

ECOmode

Activating the power-saving [ECO] mode can also help reduce the power consumption during the waiting time (standby cooling) by allowing the temperature control bands to be changed.The chamber can cool down to the set temperature within approximately 3 minutes and a half (*) after release from ECO mode.

* Under the conditions: set temperature of 4℃ at an ambient temperature of 25℃.

[ECO] MODE OFF [ECO] MODE ON
POWER CONSUMPTION 54Wh POWER CONSUMPTION 47Wh<13%DOWN>

From micro tubes to 250ml bottles

The NIX-521, with the ability to accommodate micro tubes to 250ml bottles or deep well plates, is ideal for wide range of applications. Using an optional bucket cap kit B433HS*, various types of rotors including swinging bucket rotors of biohazard-proof can be mounted.

Convenient flashing function

Convenient flashing function allows operation with preset centrifuging conditions.

*Bucket cap kit B433 is an optional kit.
HS This highly sealed rotor, which has been tested and certified by the Health Protection Agency (HPA, UK) to be compliant with the International Standard (Annex AA of the IEC 61010-2-020), meets requirements for biohazard safety. [Bucket cap kit B433] is an optional kit.

Easy to see and operate control panel

1.
Easy-to-see LCD monitor display shows various information including remaining run time, error messages, rotor types in use and records of centrifugal operation. The monitor can display in English or Japanese.

*Indication displays on the control panel in the photo is different from displays of actual operation.

2.
Dual color LED display allows the user to monitor the operation status just by looking the display; red indicates that the rotor is spinning while green indicates the rotor is stopped.

3.
Popular user-friendly Jog Dial equipped with an <ENTER> button on top enables setting to be changed quickly and more surely.

Safety & Ecology

Flap-drive system for safer and more efficient operation

Innovative Flap-drive system employed to maintain safe and efficient centrifugal operation allows a margin of error and eye-balancing of sample tubes.
*Some rotors are excepted.

  • Non-chlorine, ozone-friendly refrigeration medium which has zero ozone layer destruction coefficients is adopted.

Flex-Spin Drive

The Flex-Spin Drive features a flexible motor shaft that equalizes minor imbalances without damaging the centrifuge or triggering the imbalance protection system. This allows excellent tolerance for minor differences in sample volumes.

One-push rotor locking knob

With a single knob push, the rotor can be quickly and securely fixed.
*Some rotors are excepted.

Wide variety of rotors

Angle Rotors Spinning maximum 10,000rpm (Angle rotors only).
Swing Out Rotors From micro tubes to 250ml bottles.

Specifications

Model NIX-521
Maximum Speed 10,000rpm
Maximum RCF 11,740G
Maximum Capacity 1,536ml (Deep-well plate x 8)
Control System Microprocessor control (feedback system)
Drive Motor Induction motor
Drive System Flex-Spin drive system (Direct drive with an automatic alignment function)
Data Entry Jog Dial equipped with an <ENTER> button
Temperature Setting Range From -9℃ to +42℃ (1℃ increment)
Speed Setting Range 100 to 10,000rpm (100rpm increments)
RCF Setting Range 10 to 11,740G (10G increments for the range less than 300G,
100G increments for the range over 300G)
Time Setting Range From 10 sec to 50 sec, in 10 sec increments, from 1 min to 99 min, in 1 min increments
or <F–> for free
Safety Devices • Imbalance detector, • Lid interlock, • Lid open/close detector, • Abnormal speed detector,
• Over-current circuit breaker, • Rotor identification system, • Motor over-current detector,
• Abnormally high or low chamber temperature detector
Additional Functions • Three-step acceleration characteristics selection, • Three memory function,
• Three-step deceleration characteristics selection, • FLASH (momentary spin) function,
• Memory function for last run parameters, • BART Code selection, • Power saving (ECO) mode
Refrigerant HFC R404A (270g)
Rated Current 6.5A
Power Requirements 1-Phase 50/60Hz AC220/230/240V 8A
Power Consumption(Heat output) 1,050W (903kcal/h)
Breaker Rated breaking current 7.5A
Protection Against Electric Shock Class I
Dimensions
(except protruding portion)
540W x 597D x 858H mm,
(table height; 750mm)
Net Weight 118kg
Environmental Requirements Ambient temperature range:10 to 35℃, Relative humidity:30 to 85%,
Atmospheric pressure:700 to 1,060hPa
Intended exclusively for use indoors, Overvoltage category: II, Pollution degree: 2
Accessories Included • Operator’s manual 1, • Warranty Card 1, • BART Cord table 1,
• Clear storage case for operator’s manual 1, • Attaching screw for clear storage case 1,
• Power cord×1pc., • Spanner 1, • Level gauge 1, • Rotor locking knob 1, • Drain plug 1

※Specifications and design are subject to change for improvement without prior notice. Please ask for the latest specifications prior to your order and procurement.

See Catalog PDF for details.

* This document is created in the PDF file format.
* To view PDF files, Adobe Reader or other software is needed.
* If you don’t have Adobe Reader, click here to download its latest version.
PDF downroad NIX-521 (1.4MB)

LCX Series

Tomy
[Centrifuges]LCX-200/100

LOW SPEED BENCH-TOP CENTRIFUGE LCX-200/100

  • LCX-200LCX-200                      LCX-100LCX-100

Accessories here

Features

Mix Bucket & Mix Rack & Multi Rack

Three-step acceleration and three-step and natural deceleration

Initial values for acceleration and deceleration characteristics are set from 0 to 500rpm, however, they can be varied up to maximum speed in 100rpm increments by function settings.

From microtubes to 250ml bottles

LCX-200/100, with the ability to accommodate microtubes to 250ml bottles or deep well plates, are ideal for wide range of applications. Using an optional bucket cap kit B433 HS*, various types of rotors including swinging bucket rotors of biohazard-proof can be mounted.

Convenient flashing function

Convenient flashing function allows operation with preset centrifuging conditions.

*Bucket cap kit B433 is an optional kit.
HS This highly sealed rotor, which has been tested and certified by the Health Protection Agency (HPA, UK) to be compliant with the International Standard (Annex AA of the IEC 61010-2-020), meets requirements for biohazard safety. [Bucket cap kit B433] is an optional kit.

Easy to see and operate control panel

Easy-to-see LCD monitor display shows various information including remaining run time, error messages, rotor types in use and records of centrifugal operation.
control panel

*Indication displays on the control panel in the photo is different from displays of actual operation.

Dual color LED display allows the user to monitor the operation status just by looking the display; red indicates that the rotor is spinning while green indicates the rotor is stopped.
the display: rotor is spinning and stopped.

Safety & Convenience

Flex-Spin system for safer and more efficient operation

Innovative Flex-Spin system employed to maintain safe and efficient centrifugal operation allows a margin of error and eye-balancing of sample tubes.
*Some rotors are excepted.

• LCX-200/100 are equipped with a function to automatically reduce the rotation speed and shut the system down if it is being run over the imbalance tolerance limit.

Flex-Spin Drive [Sample Movie]

The Flex-Spin Drive features a flexible motor shaft that equalizes minor imbalances without damaging the centrifuge or triggering the imbalance protection system. This allows excellent tolerance for minor differences in sample volumes.

One-push rotor locking knob

With a single knob push, the rotor can be quickly and securely fixed.
*Some rotors are excepted.

One-push rotor locking knob diagram

Safety & Convenience Chamber Lid

The hand guard device is equipped to prevent operator’s hand and fingers from getting caught by the chamber lid.
The operator can open / close the lid and load / unload the sample tubes even though during the main power switch off.

Hand Guard Device

Compatible rotor line-up with TOMY CAX/AX/NIX-Series centrifuges

LCXシリーズはフロアタイプの多本架遠心機シリーズと共通シャフトを採用しているので、ローターの互換性があります。

LCX-Series equip common shaft with other TOMY floor type centrifuges. Various compatible rotors can be used as following centrifuges.

CAX-571
AX-521/511/501
NIX-521

※ Some of combinations of centrifuge, rotor, bucket and rack are not compatible.

Accessories here

Specifications

Model LCX-200 LCX-100
Maximum Speed 10,000rpm
Maximum RCF 11,740G
Maximum Capacity 1,000ml (250ml x 4)
Speed Control System Microprocessor feedback control
Drive Motor Induction motor
Drive System Flex-Spin drive system (Direct drive with an automatic alignment function)
Data Entry Jog Dial equipped with an <ENTER> button
Speed Setting Range 100rpm to 10,000 rpm(100rpm increments)
RCF Setting Range 10 G to 11,740 G
(Less than 300G : 10G increments, Over 300G : 100G increments)
Time Setting Range From 10 sec to 50 sec, in 10 sec increments,
from 1 min to 99 min, in 1 min increments or <F-> for free
Safety Devices • Imbalance detector • Lid interlock • Lid open/close detector • Abnormal speed detector • Over-current circuit breaker • Rotor identification system • Motor over-current detector
Additional Functions • Three-step acceleration characteristics selection • Three-step deceleration characteristics selection • Three memory function • FLASH (momentary spin) function • BART Code selection • Memory function for the last run parameters
Rated Current 120V : 10A
220/230/240V : 6A 220/230/240V : 4A
Power Requirements 1-Phase AC120V 60Hz 15A
1-Phase AC220/230/240V 50/60Hz 8A 1-Phase AC220/230/240V 50/60Hz 8A
Power Consumption(Heat output) 660W (568kcal/h) 430W (370kcal/h)
Breaker Rated breaking current 120V : 15A
Rated breaking current 220/230/240V : 7.5A Rated breaking current 220/230/240V : 7.5A
Protection Against Electric Shock Class I
Dimensions(mm) 460W x 584D x 355H (excluding hinge) 430W x 554D x 355H (excluding hinge)
Net Weight 41kg 39kg
Environmental Requirements Ambient temperature range:6 to 35℃, Relative humidity:not exceeding 75%RH,
Altitude: up to 2000m, Intended exclusively for use indoors,
overvoltage category:II, pollution degree:2, inclination:not exceeding 2 degrees
Accessories Included • Operator’s manual x1 • Warranty Card x1 • BART Code table x1 • Clear storage case for operator’s manual x1 • Rotor locking knob x1 • Power cord x1

* Specifications and design are subject to change for improvement without prior notice. Please ask for the latest specifications prior to your order and procurement.
*The above specifications show the maximum value of speed, RCF(G) and sample capacity. These values may change according to the combination of rotor, bucket, adaptor and tubes.

See Catalog PDF for details.

* This document is created in the PDF file format.
* To view PDF files, Adobe Reader or other software is needed.
* If you don’t have Adobe Reader, click here to download its latest version.
PDF downroad LCX-200 / 100 (1.51MB)

AX Series

Tomy

We offer three high capacity general purpose centrifuges,
allowing for you to choose the best model for your spplication.

Switch to Japanese

Line UP

AXシリーズ

    • AX-521
    • AX-511
    • AX-501

Accessories here

[ECO] modo

[ECO] modo Electric power saving

Activating the power-saving [ECO] mode can also help reduce the power consumption during the waiting time (standby cooling) by allowing the temperature control bands to be changed.The chamber can cool down to the set temperature within approximately 3 minutes and a half (*) after release from ECO mode.

* Under the conditions: set temperature of 4℃ at an ambient temperature of 25℃.

 

Power consumption at ECO mode

An overall increase in cooling efficiency allows for drastic reduction in energy usage during normal operation.

  • Measurement conditions: Set to 4℃ at an ambient temperature of 25℃ while centrifugation is stopped.
    (Rotors in use: AX-521/AX-321: TS-37C+3750-TC06P)
  • The values shown above are average values obtained by measuring the units.

Flexibility

Spinning maximum 10,000rpm

All angle rotors can be spun maximum 10,000rpm

CA-16
50ml x 8
10,000rpm / 11,740G
Rotor for AX-521/511/501

Three-step acceleration and three-step and natural deceleration

Initial values for acceleration and deceleration characteristics are set from 0 to 500rpm, however, they can be varied up to maximum speed in 100rpm increments by function settings.

From micro tubes to 250ml bottles

The AX-521/511/501, with the ability to accommodate micro tubes to 250ml bottles or deep well plates, is ideal for wide range of applications. Using an optional bucket cap kit B433HS*, various types of rotors including swinging bucket rotors of biohazard-proof can be mounted.

Convenient flashing function

Convenient flashing function allows operation with preset centrifuging conditions.

*Bucket cap kit B433 is an optional kit.
HS This highly sealed rotor, which has been tested and certified by the Health Protection Agency (HPA, UK) to be compliant with the International Standard (Annex AA of the IEC 61010-2-020), meets requirements for biohazard safety. [Bucket cap kit B433] is an optional kit.

Compact Design

Compact design for minimum space requirement

コンパクト設計More compact in design, compared with existing high capacity refrigerated.centrifuge, is one of the many advantages of the AX series.
AX Series are ideally suited for applications where space is limited.

Easy to see and operate control panel

1.
Easy-to-see LCD monitor display shows various information including remaining run time, error messages, rotor types in use and records of centrifugal operation. The monitor can display in English or Japanese. (AX-521)

*Indication displays on the control panel in the photo is different from displays of actual operation.

2.
Dual color LED display allows the user to monitor the operation status just by looking the display; red indicates that the rotor is spinning while green indicates the rotor is stopped.

3.
Popular user-friendly Jog Dial equipped with an <ENTER> button on top enables setting to be changed quickly and more surely.

Safety & Ecology

Flap-drive system for safer and more efficient operation

Innovative Flap-drive system employed to maintain safe and efficient centrifugal operation allows a margin of error and eye-balancing of sample tubes.
*Some rotors are excepted.

  • Non-chlorine, ozone-friendly refrigeration medium which has zero ozone layer destruction coefficients is adopted.

One-push rotor locking knob

With a single knob push, the rotor can be quickly and securely fixed.
*Some rotors are excepted.

Flex-Spin Drive

The Flex-Spin Drive features a flexible motor shaft that equalizes minor imbalances without damaging the centrifuge or triggering the imbalance protection system. This allows excellent tolerance for minor differences in sample volumes.

Specifications

Model AX-521 AX-511 AX-501
Maximum Speed 10,000rpm
Maximum RCF 11,850G
Maximum Capacity 1,536ml (Deep-well plate x 8) 1,000ml (250ml x 4)
Control System Microprocessor control (feedback system)
Drive Motor Induction motor
Drive System Flex-Spin drive system (Direct drive with an automatic alignment function)
Data Entry Jog Dial equipped with an <ENTER> button
Temperature Setting Range From -9℃ to +35℃ (1℃ increment)
Speed Setting Range 100 to 10,000rpm (100rpm increments)
RCF Setting Range 10 to 11,850G (10G increments for the range less than 300G,
100G increments for the range over 300G)
Time Setting Range From 10 sec to 50 sec, in 10 sec increments, from 1 min to 99 min, in 1 min increments
or <F–> for free
Safety Devices • Imbalance detector, • Lid interlock, • Lid open/close detector, • Abnormal speed detector,
• Over-current circuit breaker, • Rotor identification system, • Motor over-current detector,
• Abnormally high or low chamber temperature detector
Additional Functions • Three-step acceleration characteristics selection, • Three memory function,
• Three-step deceleration characteristics selection, • FLASH (momentary spin) function,
• Memory function for last run parameters, • BART Code selection, • Power saving (ECO) mode
Refrigerant HFC R404A (270g) HFC R404A (260g) HFC R404A (250g)
Rated Current 120V : 12A, 220/230/240V : 6A 120V : 10A, 220/230/240V : 5A
Power Requirements 1-Phase 50/60Hz AC120V 15A, 1-Phase 50/60Hz AC220/230/240V 8A
Power Consumption(Heat output) 970W (834kcal/h) 960W (826kcal/h) 760W (654kcal/h)
Breaker Rated breaking current 120V : 15A, 220/230/240V : 7.5A
Protection Against Electric Shock Class I
Dimensions
(except protruding portion)
540W x 597D x 858H mm,
(table height; 750mm)
510W x 567D x 858H mm,
(table height; 750mm)
462W x 540D x 858H mm,
(table height; 750mm)
Net Weight 111kg (120V)
116kg (220/230/240V)
107kg (120V)
112kg (220/230/240V)
99kg (120V)
104kg (220/230/240V)
Environmental Requirements Ambient temperature range:10 to 35℃, Relative humidity:30 to 85%,
Atmospheric pressure:700 to 1,060hPa
Intended exclusively for use indoors, Overvoltage category: II, Pollution degree: 2
Accessories Included • Operator’s manual 1, • Warranty Card 1, • BART Cord table 1,
• Clear storage case for operator’s manual 1, • Attaching screw for clear storage case 1,
• Power cord×1pc., • Spanner 1, • Level gauge 1, • Rotor locking knob 1, • Drain plug 1

※Specifications and design are subject to change for improvement without prior notice. Please ask for the latest specifications prior to your order and procurement.

 

 

LMC-4200R

Biosan

1

Description

Laboratory bench-top centrifuge with refrigeration LMC-4200R provides temperature control of biomaterial during centrifugation. Temperature control of the so-called “cold-shelf” is a gold standard for enzymologists and cell biologists because it ensures conditions necessary for reproducibility of the sample preparation stage. Temperature control absence at this stage can cause unpredictable results.

LMC-4200R is a modern centrifuge designed for operation with microtest plates and tubes from 10 to 50 ml.

Features:

  • Effective way of acceleration and deceleration:
    Run-up time 15 sec;
    Run-down time, not more 30 sec;
  • Efficient rate of chamber refrigeration: under 10 min;
  • Maintenance of stable temperature during operation;
  • User-friendly setting of centrifugation parameters (speed, temperature, time) and simultaneous display of both set and actual values;
  • Safe operation is provided by a metal protection chamber and a case cover, automatic stop at imbalance (emergency shutdown,  “IMBALANCE” displayed) and a lock keeping the lid closed while the centrifuge is running.
  • Low noise level;
  • Wide choice of accessory rotors.

1


Specification

Termperature control range
–10°C … +25°C
Stable temperature maintenance range
25°C below ambient … to +25°C
Temperature setting resolution
1°C
Speed regulation range for centrifuge tubes
100–4,200 rpm
(3,370 × g)
Speed regulation range for microtitre plates
100–2,000 rpm
(560 × g)
Speed setting resolution
100 rpm
Rotor imbalance diagnostics (automatic stop, “IMBALANCE” warning)
+
Slowdown time, not more
30 sec
Display
LCD, 2 lines
Digital time setting
1–90 min (increment 1 min)
Chamber diameter
335 mm
Dimensions
635x580x335 mm
Weight
56 kg
Nominal operating voltage
230 V, 50 Hz
Power consumption (230 V)
990 W (4.3 A)